Slate & Pebble Sealer

Bring out the natural beauty and the abundance of colours in your slate and stacked stone with the Feast Watson Slate and Pebble Sealer.

Don't sacrifice appearance in high traffic areas - you can still achieve a beautiful, gloss finish with this tough, clear sealer and top coat.

The Feast Watson Slate and Pebble Sealer will protect your non-porous stone surfaces from weather, abrasion, food, oil, grease and household dirt, while still looking achieving a classic, gloss appearance.

This product is perfect for pathways, driveways, steps and front entrances, as well as enhancing pebbles in concrete and pebble aggregate.

Note:
Slate & Pebble Sealer is easily recoatable and under normal conditions will not crack or peel. However, Slate & Pebble Sealer is NOT suitable for use on glazed or semi-glazed quarry tiles.

CAUTION: Smooth surfaces may become slippery when wet.

Safety Data Sheet

Find a stockist

WHERE TO USE

Slate and pebble floors, bathrooms, foyers, driveways, steps, pathways

FINISH

Gloss

COVERAGE RATE

10m²per litre

NUMBER OF COATS

2 coats

RECOAT TIME

2 hours

DRY TIME

8 hours

CLEAN UP

Xylene

SIZES

1L, 4L, 10L

How to prepare Feast Watson Slate and Pebble Sealer:

Preparation is key before you start coating:

Ensure your surface is thoroughly clean and free from oil, grease, dirt and moss prior to applying.
Clean the surface with Feast Watson Floorclean as per the product instructions

For new concrete and aggregate pebbles:

Allow the surface to cure for approximately 28 days then treat surface with a 10% solution (dilute) of Hydrochloric Acid.
Apply Hydrochloric Acid using a brush or mop, allow the acid to remain on the surface for 15 minutes then flush off with clean water. 3. Allow the surface to dry completely before applying Slate and Pebble Sealer.

How to apply Feast Watson Slate and Pebble Sealer:

Learn how to clear coat and protect your high traffic areas with this simple step:

Apply a minimum of two coats of Slate & Pebble Sealer using either a Feast Watson Floor Finish Applicator, brush, fine mohair or wool roller.

How to maintain your surface after using Feast Watson Slate and Pebble Sealer:

Always check on your surface to look for any signs of loss of gloss or scratches.
If an additional coat is required, clean using Feast Watson Floorclean. Apply one coat of Slate and Pebble Sealer as per application instructions.

Ensure your surface is thoroughly clean and free from oil, grease, dirt and moss prior to applying.
Clean the surface with Feast Watson Floorclean as per the product instructions

For new concrete and aggregate pebbles:

Allow the surface to cure for approximately 28 days then treat surface with a 10% solution (dilute) of Hydrochloric Acid.
Apply Hydrochloric Acid using a brush or mop, allow the acid to remain on the surface for 15 minutes then flush off with clean water. 3. Allow the surface to dry completely before applying Slate and Pebble Sealer.

APPLICATION

How to apply Feast Watson Slate and Pebble Sealer:

Learn how to clear coat and protect your high traffic areas with this simple step:

Apply a minimum of two coats of Slate & Pebble Sealer using either a Feast Watson Floor Finish Applicator, brush, fine mohair or wool roller.

MAINTENANCE

How to maintain your surface after using Feast Watson Slate and Pebble Sealer:

Always check on your surface to look for any signs of loss of gloss or scratches.
If an additional coat is required, clean using Feast Watson Floorclean. Apply one coat of Slate and Pebble Sealer as per application instructions.

Slate & Pebble Sealer

WHERE TO USE

FINISH

COVERAGE RATE

NUMBER OF COATS

RECOAT TIME

DRY TIME

CLEAN UP

SIZES

Floor Clean

Floor Finish Replacement Sock

PREPARATION

APPLICATION

MAINTENANCE

RELATED PRODUCTS

Floor Clean

Floor Finish Replacement Sock

Get the Look

Natural Look Decking – Traditional Timber Oil

Sunken Deck

Decking Re-oil

Feast Your Eyes